模具术语词汇列表
| 1 | 冲裁力 | blanking force |
|
| 2 | 卷边模 | crimping dies |
|
| 3 | 凝固化 | cure |
|
| 4 | 卷边模 | curling dies |
|
| 5 | 弹顶器 | cushion |
|
| 6 | 拉伸力 | drawing force |
|
| 7 | 拉伸比 | drawing ratio |
|
| 8 | 挤压力 | extruding force |
|
| 9 | 挤压比 | extruding ratio |
|
| 10 | 充填剂 | filler |
|
| 11 | 精冲模 | fine blanking dies |
|
| 12 | 翻边模 | flanging dies |
|
| 13 | 柔性模 | flexile dies |
|
| 14 | 颗粒料 | granule |
|
| 15 | 导柱模 | guide pillar dies |
|
| 16 | 顶件块 | kicker block |
|
| 17 | 顶件力 | kicking force |
|
| 18 | 混合机 | kneader |
|
| 19 | 切舌模 | lancing dies |
|
| 20 | 简易模 | low-cost dies |
|
| 21 | 切口模 | notching dies |
|
| 22 | 吹气成形坏料 | parison |
|
| 23 | 剖切模 | parting dies |
|
| 24 | 导正销 | pilot pin |
|
| 25 | 压料柱塞 | plunger |
|
| 26 | 预混料 | premix |
|
| 27 | 上模座 | punch holder(upper shoe) |
|
| 28 | 凸凹模 | punch-matrix |
|
| 29 | 排料孔 | relief hole |
|
| 30 | 杆直径 | shank diameter |
|
| 31 | 塑料片 | sheet |
|
| 32 | 侧压板 | side-push plate |
|
| 33 | 钢带模 | steel rule dies |
|
| 34 | 导料板 | stock guide rail |
|
| 35 | 承料板 | stock supporting plate |
|
| 36 | 挡料销 | stop pin |
|
| 37 | 热固性 | thermosetting |
|
| 38 | 扭曲模 | twisting dies |
|
| 39 | 通用模 | universal dies |
|
| 40 | 人工老化试验机 | weatherometer |
|
生词本打印版
| 1 | blanking force | 冲裁力 | |
| 2 | crimping dies | 卷边模 | |
| 3 | cure | 凝固化 | |
| 4 | curling dies | 卷边模 | |
| 5 | cushion | 弹顶器 | |
| 6 | drawing force | 拉伸力 | |
| 7 | drawing ratio | 拉伸比 | |
| 8 | extruding force | 挤压力 | |
| 9 | extruding ratio | 挤压比 | |
| 10 | filler | 充填剂 | |
| 11 | fine blanking dies | 精冲模 | |
| 12 | flanging dies | 翻边模 | |
| 13 | flexile dies | 柔性模 | |
| 14 | granule | 颗粒料 | |
| 15 | guide pillar dies | 导柱模 | |
| 16 | kicker block | 顶件块 | |
| 17 | kicking force | 顶件力 | |
| 18 | kneader | 混合机 | |
| 19 | lancing dies | 切舌模 | |
| 20 | low-cost dies | 简易模 | |
| 21 | notching dies | 切口模 | |
| 22 | parison | 吹气成形坏料 | |
| 23 | parting dies | 剖切模 | |
| 24 | pilot pin | 导正销 | |
| 25 | plunger | 压料柱塞 | |
| 26 | premix | 预混料 | |
| 27 | punch holder(upper shoe) | 上模座 | |
| 28 | punch-matrix | 凸凹模 | |
| 29 | relief hole | 排料孔 | |
| 30 | shank diameter | 杆直径 | |
| 31 | sheet | 塑料片 | |
| 32 | side-push plate | 侧压板 | |
| 33 | steel rule dies | 钢带模 | |
| 34 | stock guide rail | 导料板 | |
| 35 | stock supporting plate | 承料板 | |
| 36 | stop pin | 挡料销 | |
| 37 | thermosetting | 热固性 | |
| 38 | twisting dies | 扭曲模 | |
| 39 | universal dies | 通用模 | |
| 40 | weatherometer | 人工老化试验机 |
