模具术语词汇列表
| 1 | 风管,水轮管 | air (water)hose |
|
| 2 | 风管,水软管 | air .water hose |
|
| 3 | 动模底板 | back plate |
|
| 4 | 隔水片 | baffle |
|
| 5 | 顶块顶出 | bar ejection |
|
| 6 | 放气板 | blow-off strip |
|
| 7 | 镀铜导套 | bronze plated bushing |
|
| 8 | 隔气运水 | bubbler |
|
| 9 | 方柱镶件 | cavity insert blocks |
|
| 10 | 防腐,防锈 | corrosion resistance |
|
| 11 | 防腐塑料 | corrosive plastics |
|
| 12 | 防漏胶套筒 | drool bushing |
|
| 13 | 顶痕 | ejector mark |
|
| 14 | 顶针有高低 | ejector pins not flush |
|
| 15 | 顶针滑动 | ejector pins skid |
|
| 16 | 定模座块 | fixed clamp plate;top clamping plate;top plate |
|
| 17 | 发热管的结合剂 | heater cement |
|
| 18 | 发热管槽 | heater groove |
|
| 19 | 高抗冲塑料 | high impact plastic |
|
| 20 | 高压力软管 | high pressure hose |
|
| 21 | 高温油脂 | hightemperature grease |
|
| 22 | 动模座块 | moving clamp plate;bottom clamping plate;bottom plate |
|
| 23 | 多色注塑 | multicolor injection molding |
|
| 24 | 多浇口模具 | multigate mold |
|
| 25 | 多色注塑 | multishot injection molding |
|
| 26 | 非复位注射计数器 | no resettable shot counter |
|
| 27 | 分形面披锋 | P/L flash |
|
| 28 | 高压油表 | pressure gauge |
|
| 29 | 复位杆(回程杆) | return pin,push – back pin |
|
| 30 | 分流道拉料杆 | runner puller;runner lock pin |
|
| 31 | 封密圈 | seal ring |
|
| 32 | 二级喷嘴 | secondary nozzle |
|
| 33 | 短射,欠料注射 | short shot |
|
| 34 | 顶管顶出 | sleeve ejection |
|
| 35 | 顶棍 | stage ejector |
|
| 36 | 顶棍 | stage ejector=knock out |
|
| 37 | 顶码板 | top clamping plate |
|
| 38 | 阀门罩 | valve casing |
|
| 39 | 阀门顶出 | valve ejection |
|
| 40 | 分水板 | water manifold |
|
生词本打印版
| 1 | air (water)hose | 风管,水轮管 | |
| 2 | air .water hose | 风管,水软管 | |
| 3 | back plate | 动模底板 | |
| 4 | baffle | 隔水片 | |
| 5 | bar ejection | 顶块顶出 | |
| 6 | blow-off strip | 放气板 | |
| 7 | bronze plated bushing | 镀铜导套 | |
| 8 | bubbler | 隔气运水 | |
| 9 | cavity insert blocks | 方柱镶件 | |
| 10 | corrosion resistance | 防腐,防锈 | |
| 11 | corrosive plastics | 防腐塑料 | |
| 12 | drool bushing | 防漏胶套筒 | |
| 13 | ejector mark | 顶痕 | |
| 14 | ejector pins not flush | 顶针有高低 | |
| 15 | ejector pins skid | 顶针滑动 | |
| 16 | fixed clamp plate;top clamping plate;top plate | 定模座块 | |
| 17 | heater cement | 发热管的结合剂 | |
| 18 | heater groove | 发热管槽 | |
| 19 | high impact plastic | 高抗冲塑料 | |
| 20 | high pressure hose | 高压力软管 | |
| 21 | hightemperature grease | 高温油脂 | |
| 22 | moving clamp plate;bottom clamping plate;bottom plate | 动模座块 | |
| 23 | multicolor injection molding | 多色注塑 | |
| 24 | multigate mold | 多浇口模具 | |
| 25 | multishot injection molding | 多色注塑 | |
| 26 | no resettable shot counter | 非复位注射计数器 | |
| 27 | P/L flash | 分形面披锋 | |
| 28 | pressure gauge | 高压油表 | |
| 29 | return pin,push – back pin | 复位杆(回程杆) | |
| 30 | runner puller;runner lock pin | 分流道拉料杆 | |
| 31 | seal ring | 封密圈 | |
| 32 | secondary nozzle | 二级喷嘴 | |
| 33 | short shot | 短射,欠料注射 | |
| 34 | sleeve ejection | 顶管顶出 | |
| 35 | stage ejector | 顶棍 | |
| 36 | stage ejector=knock out | 顶棍 | |
| 37 | top clamping plate | 顶码板 | |
| 38 | valve casing | 阀门罩 | |
| 39 | valve ejection | 阀门顶出 | |
| 40 | water manifold | 分水板 |
