Computer Aided Analysis for Contact Pattern of Prolate Epicycloid Bevel and hypoid gears

摆线齿锥齿轮齿面接触区的计算器辅助分析

Denominations on Gears and Gear Pairs; Bevel and Hypoid Gears and Gear Pairs

齿轮和齿轮副的名称;伞齿轮和伞齿轮副.双曲线齿轮和双曲线齿轮副

Gear and spline drawing standards-Part 2: Bevel and hypoid gears

齿轮和花键制图标准.第2部分:伞齿轮和准双曲面齿轮

The Present Situation of Design and Manufacture of Spiral Bevel and Hypoid Gears

弧齿锥齿轮与准双曲面齿轮设计与制造的现状

Development of CAD Integration System for Hypoid Gears

弧齿准双曲面齿轮CAD集成系统开发

Tooth Surface Deviation Measurement of Hypoid Gears Based on One-dimensional Probe

基于一维测头准双曲面齿轮齿面偏差的测量

Lapping Mechanism and Experiments of Hypoid Gears

螺旋锥齿轮动态互研的机理与试验

Kinematics Analysis of Hypoid Bevel Gear with Plane Tooth

平面齿双曲线锥齿轮的运动学分析

Lapping Modification and Experiments of Hypoid Gears

研齿的修形机理与试验研究

Standard Test Method for Evaluation of the Load Carrying Capacity of Lubricants Under Conditions of Low Speed and High Torque Used for Final Hypoid Drive Axles

用终端偏轴伞齿轮驱动轴在低速和高扭矩条件下评估润滑油承载能力的标准试验方法

Calculation of scuffing load capacity of cylindrical, bevel and hypoid gears-Part 1: Flash temperature method

圆柱齿轮、锥齿轮和双曲线齿轮啮合承载能力的计算 第1部分:瞬现温度法

Calculation of scuffing load capacity of cylindrical, bevel and hypoid gears-Part 2: Integral temperature method

圆柱齿轮、锥齿轮和双曲线齿轮啮合承载能力的计算 第2部分:积分温度法

Calculation of scuffing load capacity of cylindrical, bevel and hypoid gears-Integral temperature method

圆柱形齿轮、伞齿轮和准双曲面齿轮的磨损承载能力的计算方法.累积温度法

Calculation of scuffing load capacity of cylindrical, bevel and hypoid gears-Flash temperature method

圆柱形齿轮、伞齿轮和准双曲面齿轮磨损承载能力的计算.闪蒸温度法

Calculation of scuffing load capacity of cylindrical, bevel and hypoid gears-Part 1: Flash temperature method

圆柱形锥齿轮和准双曲面齿轮的磨损承载能力的计算方法.第1部分:闪蒸温度法

Calculation of scuffing load capacity of cylindrical, bevel and hypoid gears-Part 2: Integral temperature method

圆柱形锥齿轮和准双曲面齿轮的磨损承载能力的计算方法.第2部分:累积温度法

Dependability Optimal Design on the Speed Reducers of Launching Type Hypoid Gears

展开式斜齿圆柱齿轮减速器可靠性优化设计

Test Method for Evaluation of the Load Carrying Capacity of Lubricants under Conditions of Low Speed and High Torque Used for Final Hypoid Drive Axles

主动双曲面驱动轴用润滑剂在低速和大扭力条件下载荷能力评价的试验方法

Final gear ratio (Hypoid final gear)

主减速齿轮比(双曲线主减速齿轮)

The Theoretical Analysis and Experimental Investigation of the Vibration in Hypoid Gear System

准双曲齿疗齿轮系统振动的理论分析与试验研究

Generation of HFT Hypoid Pinion Fillet Surfaces and the Test for Undercutting and Interference with Gear Top

HFT准双曲面齿轮的齿根过渡曲面和干涉、根切检验

Design of Shrinkage Tooth with Equal Tip Clearance of Hypoid Bevel Gear Pair with Half Generating Method

半展成法收缩齿等顶隙准双曲面锥齿轮副设计

The Design and Analysis to Hypoid Gear of High Speed Ratio

大速比准双曲面齿轮的设计与分析

Discussion on Noise Reduction of Hypoid Bevel Gear

对降低准双曲面锥齿轮噪声的探索

Loaded Tooth Contact Analysis for Hypoid Gears with Long Tooth Height

高齿准双曲面齿轮的轮齿加载接触分析

Design Theory and Experiments of Hypoid Gear with High Tooth

高齿准双曲面齿轮的设计方法与试验研究

New Design Method to Hypoid Gear of High Strength

高强度准双曲面齿轮的新设计方法

The Study of Simulating for Spiral Bevel and Hypoid Gears Processing

弧齿锥齿轮的加工仿真研究

Study on Model of Spiral Bevel and Hypoid Gear Pre- lapping

弧齿锥齿轮定制研磨加工模型研究

Automatic selection of transmission parameter of spiral bevel gear and hypoid gear

弧齿锥齿轮和双曲线齿轮传动参数自动选择

hypoid oil

n.双曲线齿轮油

hypoid axle

双曲面齿轮传动

hypoid-gear

n.双曲线齿轮

hypoid gear

准双曲面齿轮

hypoid bevel

准双曲面伞齿轮(传动), 偏轴伞齿轮(传动)

hypoid gearing

n.内摆线齿轮啮合,内摆线齿轮传动装置

hypoid gear oil

n.双曲线齿轮油

hypoid lubricant

n.双曲线齿轮用润滑剂

hypoid generator

准双曲面齿轮加工机床

hypoid gear pair

准双曲面齿轮副

hypoid gear tester

准双曲面齿轮滚动检查机

hypoid drive pinion

n.主动准双曲线伞齿轮,主偏轴伞齿轮

hypoid pinion offset

双曲线齿轮[螺旋]传动的偏心距

offset of hypoid gears

准双进齿轮补偿