模具术语词汇列表
| 1 | 输送管;导管 | (cooling)duct |
|
| 2 | 三辨 | 3-flute |
|
| 3 | 四辨 | 4-flute |
|
| 4 | 适配模板 | adapter plate |
|
| 5 | 水口铁 | bridge piece |
|
| 6 | 铜导套 | bronze bushing |
|
| 7 | 铜基石墨 | bronze with graphite |
|
| 8 | 商品目录编码 | catalog item |
|
| 9 | 山打距离(中心线距离) | center distance (CRS) |
|
| 10 | 锁模吨位 | clamping tonnage |
|
| 11 | 凸锣刀片 | convex cutter |
|
| 12 | 铜公 | copper electrode |
|
| 13 | 深厚计 | Depth Gauge |
|
| 14 | 司筒,顶套 | ejection sleeve |
|
| 15 | 上顶针板 | ejector retainer plate |
|
| 16 | 扇形入口 | fan gate |
|
| 17 | 扇形入水 | fan gate |
|
| 18 | 碎硬 | harden/nitride |
|
| 19 | 水喉箍 | hose clip |
|
| 20 | 水平器 | leveller |
|
| 21 | 手办 | mock-up;prototype |
|
| 22 | 砂模夹(注塑机使用) | mould clamps;lifting clamp |
|
| 23 | 射嘴板 | nozzle plate |
|
| 24 | 塑料模钢 | plastic mould steel |
|
| 25 | 水口铁 | puller bar |
|
| 26 | 突模固定板 | punch-retainer plate |
|
| 27 | 提刀速率 | retract rate |
|
| 28 | 塞打螺丝 | S.H.S.B. |
|
| 29 | 丝印机 | screen printer |
|
| 30 | 缩坑 | sink mark |
|
| 31 | 射台 | sled |
|
| 32 | 双头刀 | split double end |
|
| 33 | 条纹,条痕 | streak |
|
| 34 | 双向切削 | Tee slot cutter |
|
| 35 | 蚀纹 | texturing |
|
| 36 | 上模座块 | upper clamping plate |
|
| 37 | 疏气孔 | vent |
|
| 38 | 疏气塞 | venting plug |
|
| 39 | 疏气阀 | venting valves |
|
| 40 | 水路集成块 | water manifold |
|
生词本打印版
| 1 | (cooling)duct | 输送管;导管 | |
| 2 | 3-flute | 三辨 | |
| 3 | 4-flute | 四辨 | |
| 4 | adapter plate | 适配模板 | |
| 5 | bridge piece | 水口铁 | |
| 6 | bronze bushing | 铜导套 | |
| 7 | bronze with graphite | 铜基石墨 | |
| 8 | catalog item | 商品目录编码 | |
| 9 | center distance (CRS) | 山打距离(中心线距离) | |
| 10 | clamping tonnage | 锁模吨位 | |
| 11 | convex cutter | 凸锣刀片 | |
| 12 | copper electrode | 铜公 | |
| 13 | Depth Gauge | 深厚计 | |
| 14 | ejection sleeve | 司筒,顶套 | |
| 15 | ejector retainer plate | 上顶针板 | |
| 16 | fan gate | 扇形入口 | |
| 17 | fan gate | 扇形入水 | |
| 18 | harden/nitride | 碎硬 | |
| 19 | hose clip | 水喉箍 | |
| 20 | leveller | 水平器 | |
| 21 | mock-up;prototype | 手办 | |
| 22 | mould clamps;lifting clamp | 砂模夹(注塑机使用) | |
| 23 | nozzle plate | 射嘴板 | |
| 24 | plastic mould steel | 塑料模钢 | |
| 25 | puller bar | 水口铁 | |
| 26 | punch-retainer plate | 突模固定板 | |
| 27 | retract rate | 提刀速率 | |
| 28 | S.H.S.B. | 塞打螺丝 | |
| 29 | screen printer | 丝印机 | |
| 30 | sink mark | 缩坑 | |
| 31 | sled | 射台 | |
| 32 | split double end | 双头刀 | |
| 33 | streak | 条纹,条痕 | |
| 34 | Tee slot cutter | 双向切削 | |
| 35 | texturing | 蚀纹 | |
| 36 | upper clamping plate | 上模座块 | |
| 37 | vent | 疏气孔 | |
| 38 | venting plug | 疏气塞 | |
| 39 | venting valves | 疏气阀 | |
| 40 | water manifold | 水路集成块 |
