1 | 加速顶针 | accelerated ejector |
|
2 | 加速顶棍 | accelerated knock out |
|
3 | 合金镶件 | alloy insert |
|
4 | 化学成份 | chemical composition |
|
5 | 环形运动 | circular motion |
|
6 | 后模镶件 | core sub-insert |
|
7 | 合金压铸 | die cast |
|
8 | 火花纹 | EDM marks |
|
9 | 胶样 | epoxy |
|
10 | 挤出,挤塑 | extrusion |
|
11 | 加热圈 | heater band |
|
12 | 喉咀套 | jiffy-matic socket |
|
13 | 喉咀公 | jiffy-tite plug |
|
14 | 接头,连接 | joint |
|
15 | 加工路径 | machining path |
|
16 | 夹痕;夹水纹 | mismatch |
|
17 | 夹纹 | mismatch;witness line |
|
18 | 环绕切削 | parallel spiral |
|
19 | 环切并清角 | parallel spiral clean corners |
|
20 | 进刀率 | plunge rate |
|
21 | 精密冲模 | precisiion blanking die |
|
22 | 精密冲模 | precision blanking die |
|
23 | 将...淬火,使冷却 | quench steel |
|
24 | 铰大圆孔直径 | ream |
|
25 | 红外线接受器 | receiver |
|
26 | 回用料 | regrind |
|
27 | 介子座 | spacer rail |
|
28 | 唧嘴有管钉 | sprue bushing-keyed |
|
29 | 唧嘴R尺寸 | sprue orifice and radius size |
|
30 | 唧嘴突出高度 | sprue pretrusion |
|
31 | 唧咀扣针 | sprue puller pin |
|
32 | 浇口分流锥 | sprue spreader |
|
33 | 阶梯式顶杆 | stepped ejector pin |
|
34 | 夹水纹 | stress marks |
|
35 | 活动板,推料板 | stripper plate |
|
36 | 较薄的料位 | thin steel section |
|
37 | 简化型细水口系统 | three plate type system |
|
38 | 回撞装置 | toggle-lok |
|
39 | 喉咀 | water junction |
|
40 | 夹水纹/流纹 | witness line;mismatch;stress marks |
|
1 | accelerated ejector | 加速顶针 | |
2 | accelerated knock out | 加速顶棍 | |
3 | alloy insert | 合金镶件 | |
4 | chemical composition | 化学成份 | |
5 | circular motion | 环形运动 | |
6 | core sub-insert | 后模镶件 | |
7 | die cast | 合金压铸 | |
8 | EDM marks | 火花纹 | |
9 | epoxy | 胶样 | |
10 | extrusion | 挤出,挤塑 | |
11 | heater band | 加热圈 | |
12 | jiffy-matic socket | 喉咀套 | |
13 | jiffy-tite plug | 喉咀公 | |
14 | joint | 接头,连接 | |
15 | machining path | 加工路径 | |
16 | mismatch | 夹痕;夹水纹 | |
17 | mismatch;witness line | 夹纹 | |
18 | parallel spiral | 环绕切削 | |
19 | parallel spiral clean corners | 环切并清角 | |
20 | plunge rate | 进刀率 | |
21 | precisiion blanking die | 精密冲模 | |
22 | precision blanking die | 精密冲模 | |
23 | quench steel | 将...淬火,使冷却 | |
24 | ream | 铰大圆孔直径 | |
25 | receiver | 红外线接受器 | |
26 | regrind | 回用料 | |
27 | spacer rail | 介子座 | |
28 | sprue bushing-keyed | 唧嘴有管钉 | |
29 | sprue orifice and radius size | 唧嘴R尺寸 | |
30 | sprue pretrusion | 唧嘴突出高度 | |
31 | sprue puller pin | 唧咀扣针 | |
32 | sprue spreader | 浇口分流锥 | |
33 | stepped ejector pin | 阶梯式顶杆 | |
34 | stress marks | 夹水纹 | |
35 | stripper plate | 活动板,推料板 | |
36 | thin steel section | 较薄的料位 | |
37 | three plate type system | 简化型细水口系统 | |
38 | toggle-lok | 回撞装置 | |
39 | water junction | 喉咀 | |
40 | witness line;mismatch;stress marks | 夹水纹/流纹 |